manualshive.com logo in svg

Domino G Series, Руководство по эксплуатации продукта, Страница: 157 / 172

Поделиться
Скачать
Domino G Series Скачать руководство пользователя страница 157

UPDATE SOFTWARE/FIRMWARE

To update the printer's software/firmware:

1. Put the update file into the top level (root folder) of a USB memory device.

1.
2. Stop printing.

2.
3. Connect the USB memory device to the printer.

3.

4. From the 

Home 

screen, select the 

Update 

icon: 

4.

5. Select the

 Select file icon: 

5.

6. Open the D:/ drive: 

6.
7. Select the update file, to complete "Step 1".

7.

1.

Notes

Update files have an .io extension.

1.

2. If the update file cannot be seen, select the 

Refresh 

icon: 

2.

8. Select 

Next,

 to upload the file to the printer and complete "Step 2".

8.

Note

Do not remove the USB memory device, until the file is uploaded to the

printer.

9. Select 

Next

, to verify the update file and complete "Step 3".

9.
10. After the file is verified, select 

Next 

to install the update file and complete "Step 4".

10.

1.

Notes

Do not turn off the printer, disconnect the printer from electrical power, or

1.

change the screen until the update file has installed.

2. After the update file has successfully installed, the printer will automatically

2.

restart.

11. After the printer has restarted, the printer is ready for use.

11.

MAINTENANCE & TROUBLESHOOTING

EPT077343 EN - Issue 1 - 11 November 2022

157

Содержание G Series













































































































































































Отзывы:

Нет отзывов