background image

[page 4]  |  gpelectric.com

SAFETY PRECAUTIONS

WARNING!

Personal Injur

y

Working in the vicinity of a lead acid battery is 

dangerous. Batteries can generate explosive gases 

during operation. Never smoke or allow a spark or 

flame in the vicinity of a battery. Provide sufficient 

ventilation around the battery.

Wear eye and clothing protection. Avoid touching 

eyes while working near batteries. Wash your hands 

when done.

If battery acid contacts skin or clothing, wash them 

immediately with soap and water. If acid enters 

an eye, immediately flood the eye with running 

cold water for at least 15 minutes and get medical 

attention immediately.

Be careful when using metal tools in the vicinity of 

batteries. Dropping a metal tool onto a battery might 

cause a short circuit and possibly an explosion.

Ensure that children, pets, and other animals are kept 

away from the inverter, solar arrays, battery bank, 

and utility grid components.

Remove personal metal items such as rings, bracelets, 

necklaces, and watches when working with a battery. 

A battery can produce a short circuit current high 

enough to melt objects such as rings, causing severe 

burns.

Содержание GP-BMK-25















Отзывы: