background image

DOMEL  

 

EC – Controller Compacto 

V2.0, July 2014  

Operating and installation Instructions  

 

This  Installation  guide  contains  the  information  necessary  for  safety.  Installation  and  basic 
running of the EC 

– Controller. 

 

1.  GENERAL SAFATEY 

Danger!

 

Electric voltage on the device 

EC-Drive must only be connected, instale, modified or repaired by a qualified 
person!  Incorrect  mounting  could  cause  material  damage  and  risk  of  fatal 
injury  from  electric  shock!  Domel  is  not  responsible  for  any  damage 
caused  by  incorrect  or  bad  circuit  connection  or  by  non-professional 
installation! 

Use fuses for power lines. Install all earth wires. Before operating check the 
wires  for  short  circuits.  Use  only  cables  that  meet  the  specified  installation 
requirements for voltage, current, insulation material, load etc. 

 

Warning!

 

Electric voltage! 

Never  open  EC-Controller  or  parts  of  them  when  the  main  supply  is 
connecting.  It  can  be  extremely  dangerous  and  could  cause  risk  of  fatal 
injury from electric shock! 

When is necessary to touch high voltages lines, disconnect the main supply 
voltage and wait at least 5 minutes before servicing the drive. 

 

Note! 

It is the responsibility of the user or installer to ensure correct grounding and 
protection in accordance with national and local standards. 

 

1.1. 

Personal Safety 

The 

[Start  /  Stop]

  input on  the  user  interface  panel  of  the  EC  drive  does  not  disconnect  the 

drive from the AC line. Do not use it as a safety switch. 

Do  not  remove  the  terminal  lines  for  the  motor  and  AC  line  supply  while  the  EC  drive  is 
connected  to  the  AC  line.  Ensure  that  the  AC  line  supply  has  been  disconnected  and  wait 
5 minutes before removing motor and AC lines. 

The motor can be started by means of digital commands, bus commands, references or local 
start command whenever the drive is connected to the AC line. Therefore, an unintended start 
may  occur  anytime  power  is  applied.  Never  service  the  drive  or  equipment  when  power  is 
applied to the drive. 

Before installing and operating EC-controller please read this instruction carefully! 

Содержание Compacto
























Отзывы: