Dolphin PTM 216Z Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 43

Dolphin PTM 216Z Скачать руководство пользователя страница 22

USER MANUAL

PTM 216Z – 2.4 GHz Zigbee Generic Switch Pushbutton Transmitter Module

© 2018 EnOcean | www.enocean.com

F-710-017, V1.0

PTM 216Z User Manual | v1.2 | November 2018 | Page 22/43

5.3

Sequential commissioning

Sequential commissioning is intended for the case where the intended receiver or network

does not operate on one of the primary radio channels or where direct commissioning is not
practical due to the mechanical constraints of the switch design (e.g. for single rocker
switches).

Sequential commissioning allows selecting any of the 16 radio channels and can be execut-
ed even on single rocker switches. It is however more complex than direct commissioning

and therefore recommended mainly for cases where direct commissioning cannot be used.

5.3.1

Commissioning request

Commissioning requests are triggered using a special button contact sequence. This is illus-
trated in Figure 14 below.

Figure 14 – Button sequence for commissioning mode

«
...
20
21
22
23
24
...
»

Содержание PTM 216Z












































Отзывы:

Нет отзывов