manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

ground. There should be no continuity. If OK, diag-
nose the CTM and its inputs using a DRBIII

t

scan

tool. Refer to the appropriate diagnostic procedures.
If not OK, repair the shorted high beam indicator
driver circuit between the CTM and the instrument
cluster as required.

LOW FUEL INDICATOR

DESCRIPTION

A low fuel indicator is standard equipment on all

instrument clusters. The low fuel indicator is located
in the Information Center area of the instrument
cluster overlay, to the left of center. The low fuel indi-
cator consists of a stenciled cutout of the Interna-
tional Control and Display Symbol icon for “Fuel” in
the opaque layer of the instrument cluster overlay.
The dark outer layer of the overlay prevents the indi-
cator from being clearly visible when it is not illumi-
nated. An amber lens behind the cutout in the
opaque layer of the overlay causes the icon to appear
in amber through the translucent outer layer of the
overlay when the indicator is illuminated from
behind by a Light Emitting Diode (LED) soldered
onto the instrument cluster electronic circuit board.
The low fuel indicator is serviced as a unit with the
instrument cluster.

OPERATION

The low fuel indicator gives an indication to the

vehicle operator when the level of fuel in the fuel
tank becomes low. This indicator is controlled by a
transistor on the instrument cluster circuit board
based upon cluster programming and electronic mes-
sages received by the cluster from the Powertrain
Control Module (PCM) over the Programmable Com-
munications Interface (PCI) data bus. The low fuel
indicator Light Emitting Diode (LED) receives bat-
tery current on the instrument cluster electronic cir-
cuit board through the fused ignition switch output
(run-start) circuit whenever the ignition switch is in
the On or Start positions; therefore, the LED will
always be off when the ignition switch is in any posi-
tion except On or Start. The LED only illuminates
when it is provided a path to ground by the instru-
ment cluster transistor. The instrument cluster will
turn on the low fuel indicator for the following rea-
sons:

•

Bulb Test - Each time the ignition switch is

turned to the On position the indicator is illuminated
for about two seconds as a bulb test.

•

Less Than 12.5 Percent Tank Full Message -

Each time the cluster receives messages from the
PCM indicating the percent tank full is 12.5 (one-
eighth) or less for 10 consecutive seconds and the

vehicle speed is zero, or for 60 consecutive seconds
and the vehicle speed is greater than zero, the low
fuel indicator is illuminated and a single chime tone
is sounded. The low fuel indicator remains illumi-
nated until the cluster receives messages from the
PCM indicating that the percent tank full is greater
than 12.5 (one-eighth) for 10 consecutive seconds and
the vehicle speed is zero, or for 60 consecutive sec-
onds and the vehicle speed is greater than zero, or
until the ignition switch is turned to the Off position,
whichever occurs first. The chime tone feature will
only repeat during the same ignition cycle if the low
fuel indicator is cycled off and then on again by the
appropriate percent tank full messages from the
PCM.

•

Less Than Empty Percent Tank Full Mes-

sage - Each time the cluster receives a message from
the PCM indicating the percent tank full is less than
empty, the low fuel indicator is illuminated immedi-
ately. This message would indicate that the fuel tank
sender input to the PCM is a short circuit.

•

More Than Full Percent Tank Full Message

- Each time the cluster receives a message from the
PCM indicating the percent tank full is more than
full, the low fuel indicator is illuminated immedi-
ately. This message would indicate that the fuel tank
sender input to the PCM is an open circuit.

•

Actuator Test - Each time the cluster is put

through the actuator test, the indicator will be
turned on, then off again during the bulb check por-
tion of the test to confirm the functionality of the
LED and the cluster control circuitry.

The PCM continually monitors the fuel tank send-

ing unit, then sends the proper messages to the
instrument cluster. For further diagnosis of the low
fuel indicator or the instrument cluster circuitry that
controls the LED, (Refer to 8 - ELECTRICAL/IN-
STRUMENT CLUSTER - DIAGNOSIS AND TEST-
ING). For proper diagnosis of the fuel tank sending
unit, the PCM, the PCI data bus, or the message
inputs to the instrument cluster that control the low
fuel indicator, a DRBIII

t

scan tool is required. Refer

to the appropriate diagnostic information.

MALFUNCTION INDICATOR
LAMP (MIL)

DESCRIPTION

A Malfunction Indicator Lamp (MIL) is standard

equipment on all instrument clusters. The MIL is
located in the Information Center area of the instru-
ment cluster overlay, to the left of center. The MIL
consists of a stencilled cutout of the International
Control and Display Symbol icon for “Engine” in the
opaque layer of the instrument cluster overlay. The

AN

INSTRUMENT CLUSTER

8J - 23

HIGH BEAM INDICATOR (Continued)

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Бренд: Daihatsu Страницы: 43
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
EZTRUNK PHANTOM JK Assembly Manual preview
PHANTOM JK
Бренд: EZTRUNK Страницы: 3
B-Speech Sima User Manual preview
Sima
Бренд: B-Speech Страницы: 4
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
Fiat Fiat Bravo LPG Owner'S Manual preview
Fiat Bravo LPG
Бренд: Fiat Страницы: 24
Valeo AS1A Owner'S Manual preview
AS1A
Бренд: Valeo Страницы: 28
ICON 91824E Installation Instructions preview
91824E
Бренд: ICON Страницы: 4
National Cycle Quantum Wash'n'Wipe N30208 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30208
Бренд: National Cycle Страницы: 12
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Бренд: Oldsmobile Страницы: 340
Edelbrock 2917 Nstallation Instructions preview
2917 Nstallation
Бренд: Edelbrock Страницы: 1
BMW M3 SEDAN Owner'S Manual preview
M3 SEDAN
Бренд: BMW Страницы: 392
Curt Manufacturing 13434 Installation Instructions preview
13434
Бренд: Curt Manufacturing Страницы: 4
true-i HMBS-200 User Manual preview
HMBS-200
Бренд: true-i Страницы: 11
Classic AutoAir Mustang 1969 Installation Manual preview
Mustang 1969
Бренд: Classic AutoAir Страницы: 44
Bilstein E4-WM5-Y479A00 Mounting Instruction preview
E4-WM5-Y479A00
Бренд: Bilstein Страницы: 7
Gentex ADVGEN20A Manual preview
ADVGEN20A
Бренд: Gentex Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды