manualshive.com logo in svg

Dodge Dakota 2001, Руководство по обслуживанию

Service Manual для Dodge Dakota 2001 - это подробное руководство, которое поможет вам обслуживать и ремонтировать ваш автомобиль. Скачайте это руководство бесплатно с manualshive.com и сохраните его для использования в любое удобное время. Надежное руководство для вашего Dodge Dakota 2001!

Поделиться
Скачать
background image

DOOR AJAR INDICATOR

DESCRIPTION

A door ajar indicator is standard equipment on all

instrument

clusters.

However,

on

vehicles

not

equipped with this optional feature, this indicator is
electronically disabled. The door ajar indicator is
located in the Information Center area of the instru-
ment cluster, to the left of center. The door ajar indi-
cator consists of a stenciled cutout of the words
“DOOR AJAR” in the opaque layer of the instrument
cluster overlay. The dark outer layer of the overlay
prevents the indicator from being clearly visible
when it is not illuminated. A red lens behind the cut-
out in the opaque layer of the overlay causes the
“DOOR AJAR” text to appear in red through the
translucent outer layer of the overlay when the indi-
cator is illuminated from behind by a Light Emitting
Diode (LED) soldered onto the instrument cluster
electronic circuit board. The door ajar indicator is
serviced as a unit with the instrument cluster.

OPERATION

The door ajar indicator gives an indication to the

vehicle operator that one or more of the passenger
compartment doors may be open or not completely
latched. This indicator is controlled by a transistor
on the instrument cluster circuit board based upon
cluster

programming

and

electronic

messages

received by the cluster from the Central Timer Mod-
ule (CTM) over the Programmable Communications
Interface (PCI) data bus. The door ajar indicator
Light Emitting Diode (LED) receives battery current
on the instrument cluster electronic circuit board
through the fused ignition switch output (run-start)
circuit whenever the ignition switch is in the On or
Start positions; therefore, the LED will always be off
when the ignition switch is in any position except On
or Start. The LED only illuminates when it is pro-
vided a path to ground by the instrument cluster
transistor. The instrument cluster will turn on the
door ajar indicator for the following reasons:

•

Bulb Test - Each time the ignition switch is

turned to the On position the door ajar indicator is
illuminated for about two seconds as a bulb test.

•

Door Ajar Lamp-On Message - Each time the

cluster receives a door ajar lamp-on message from
the CTM indicating that a door is open or not com-
pletely latched, the door ajar indicator will be illumi-
nated. The indicator remains illuminated until the
cluster receives an door ajar lamp-off message from
the CTM, or until the ignition switch is turned to the
Off position, whichever occurs first.

•

Actuator Test - Each time the cluster is put

through the actuator test, the door ajar indicator will
be turned on, then off again during the bulb check

portion of the test to confirm the functionality of the
cluster control circuitry.

The CTM continually monitors the door ajar

switches to determine the status of the doors. The
CTM then sends the proper door ajar lamp-on and
lamp-off messages to the instrument cluster. For fur-
ther diagnosis of the door ajar indicator or the
instrument cluster circuitry that controls the indica-
tor,

(Refer

to

8

-

ELECTRICAL/INSTRUMENT

CLUSTER

-

DIAGNOSIS AND

TESTING).

For

proper diagnosis of the door ajar switches and cir-
cuits, (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING
- INTERIOR/DOOR AJAR SWITCH - DIAGNOSIS
AND TESTING). For proper diagnosis of the CTM,
the PCI data bus, or the message inputs to the
instrument cluster that control the door ajar indica-
tor, a DRBIII

t

scan tool is required. Refer to the

appropriate diagnostic information.

ENGINE TEMPERATURE
GAUGE

DESCRIPTION

An engine coolant temperature gauge is standard

equipment on all instrument clusters. The engine
coolant temperature gauge is located in the lower left
quadrant of the instrument cluster, below the voltage
gauge. The engine coolant temperature gauge con-
sists of a movable gauge needle or pointer controlled
by the instrument cluster circuitry and a fixed 90
degree scale on the cluster overlay that reads left-to-
right from “C” (or Cold) to “H” (or Hot) for all
engines. An International Control and Display Sym-
bol icon for “Engine Coolant Temperature” is located
on the cluster overlay, in the center of the gauge
directly above the hub of the gauge needle. The
engine coolant temperature gauge graphics are white
against a black field except for a single red gradua-
tion at the high end of the gauge scale, making them
clearly visible within the instrument cluster in day-
light. When illuminated from behind by the panel
lamps dimmer controlled cluster illumination lighting
with the exterior lamps turned On, the white graph-
ics appear blue-green and the red graphics appear
red. The orange gauge needle is internally illumi-
nated. Gauge illumination is provided by replaceable
incandescent bulb and bulb holder units located on
the instrument cluster electronic circuit board. The
engine coolant temperature gauge is serviced as a
unit with the instrument cluster.

OPERATION

The engine coolant temperature gauge gives an

indication to the vehicle operator of the engine cool-
ant temperature. This gauge is controlled by the

8J - 18

INSTRUMENT CLUSTER

AN

Содержание Dakota 2001




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dakota 2001

Valeo SC400 Operating Instructions Manual preview
SC400
Бренд: Valeo Страницы: 17
Pivot DXB-B User Manual preview
DXB-B
Бренд: Pivot Страницы: 4
Velleman CAMCOLC1N User Manual preview
CAMCOLC1N
Бренд: Velleman Страницы: 6
Toyota 1973 Crown Hardtop Owner'S Manual preview
1973 Crown Hardtop
Бренд: Toyota Страницы: 50
Chevrolet 1999 Malibu Owner'S Manual preview
1999 Malibu
Бренд: Chevrolet Страницы: 344
Prorack K692 Fitting Instructions Manual preview
K692
Бренд: Prorack Страницы: 15
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Бренд: Safe Fleet Страницы: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Бренд: Seat Страницы: 44
Meta System FrontPlate4 Manual preview
FrontPlate4
Бренд: Meta System Страницы: 16
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Бренд: VER-MAC Страницы: 64
E&G Classics 1409-0102-10 Installation Instructions preview
1409-0102-10
Бренд: E&G Classics Страницы: 3
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Бренд: Black+Decker Страницы: 21
Beeper RW050RF User& Installer'S Manual preview
RW050RF
Бренд: Beeper Страницы: 20
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Бренд: Safe Fleet Страницы: 12
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Бренд: Acura Страницы: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Бренд: Ford Страницы: 325
TOGU Airgo Active cushion / Comfort Manual And Maintenance Instructions preview
Airgo Active cushion / Comfort
Бренд: TOGU Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды