Dodge 2016 Viper SRT ACR Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 427

background image

position. If necessary, slide the latch plate down the
webbing to allow the seat belt to retract fully.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the

anchor point.

2. At about 6 to 12 in (15 to 30 cm) above the latch plate,

grasp and twist the seat belt webbing 180 degrees to
create a fold that begins immediately above the latch
plate.

3. Slide the latch plate upward over the folded webbing.

The folded webbing must enter the slot at the top of
the latch plate.

4. Continue to slide the latch plate up until it clears the

folded webbing and the seat belt is no longer twisted.

Seat Belt Extender

If a seat belt is not long enough to fit properly, even when
the webbing is fully extended and the adjustable upper
shoulder belt anchorage (if equipped) is in its lowest
position, your authorized dealer can provide you with a
Seat Belt Extender. The Seat Belt Extender should be used
only if the existing seat belt is not long enough. When the
Seat Belt Extender is not required for a different occu-
pant, it must be removed.

42

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
42
43
44
45
46
...
»

Содержание 2016 Viper SRT ACR












































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2016 Viper SRT ACR

Бренд: GATmatic Страницы: 13

Бренд: EUFAB Страницы: 52

Бренд: Waeco Страницы: 172

Бренд: VBG Страницы: 16

Бренд: FALCON RIDGE Страницы: 7

Бренд: Volvo Страницы: 30

Бренд: Westin Страницы: 3

Бренд: Audiovox Страницы: 3

Бренд: Victory 4x4 Страницы: 9

Бренд: S3 Power Sports Страницы: 2

2004 Impreza OUTBACK SPORT

Бренд: Subaru Страницы: 34

Бренд: Mitsubishi MOTORS Страницы: 416

Бренд: BrandMotion Страницы: 6

Бренд: POOL-LINE Страницы: 2

Interlock 700 Series

Бренд: Scania Страницы: 82

Бренд: Z Flash Страницы: 4

Бренд: Classic AutoAir Страницы: 44

Бренд: Car-Interface Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды