Dodge 2016 Viper SRT ACR Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 427

background image

2. Push and hold the desired HomeLink button until the

indicator light begins to flash after 20 seconds.

Do not

release the button.

3.

Without

releasing

the

button

proceed

with

“Canadian/Gate Operator Programming” step 2 and
follow all remaining steps.

Using HomeLink

To operate, push and release the programmed HomeLink
button. Activation will now occur for the programmed
device (i.e. garage door opener, gate operator, security
system, entry door lock, home/office lighting, etc.) The
hand-held transmitter of the device may also be used at
any time.

Security

It is advised to erase all channels before you sell or turn
in your vehicle.

To do this, push and hold the two outside buttons for 20
seconds until the red indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.

The HomeLink Universal Transceiver is disabled when
the Vehicle Security Alarm is active.

Troubleshooting Tips

If you are having trouble programming HomeLink, here
are some of the most common solutions:

•

Replace the battery in the Garage Door Opener hand-
held transmitter.

•

Push the LEARN button on the Garage Door Opener
to complete the training for a Rolling Code.

•

Did you unplug the device for programming and
remember to plug it back in?

132

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
132
133
134
135
136
...
»

Содержание 2016 Viper SRT ACR












































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2016 Viper SRT ACR

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

3-series convertible

Бренд: BMW Страницы: 98

Бренд: STC Страницы: 6

Бренд: HAUL MASTER Страницы: 8

Бренд: Quadratec Страницы: 6

Бренд: Jaeger Страницы: 11

Бренд: v.link Страницы: 12

Бренд: Broadfeet Страницы: 2

Бренд: Chevrolet Страницы: 46

Бренд: Easee Страницы: 21

Бренд: Toyota Страницы: 26

Бренд: Discount Car Stereo Страницы: 11

Бренд: Ultraplast Страницы: 5

Бренд: AL-KO Страницы: 88

Бренд: Hollywood Racks Страницы: 8

Бренд: Peiying Страницы: 28

2005 Grand Cherokee

Бренд: Jeep Страницы: 408

Бренд: Monzana Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды