Docomo Style F-02D, Инструкция по эксплуатации

Страница: 139 / 150

29
AT&E<n>
*1
Set the speed display used when connection is made.
n=0 : Display communication speed of wireless zone
n=1 : Display communication speed between a PC and FOMA terminal (default)
AT&E1
OK
AT&F Reset the current setting to the default.
When this command is executed during communication, the terminal is reset after the line
is disconnected (displaying "NO CARRIER").
AT&F
OK (When in offline mode)
AT&S<n>
*1
Set control of the data set ready (DR) signal to be output to DTE.
n=0 : Always ON (default) n=1 : ON at time of connection
AT&S0
OK
AT&W Register the current settings in FOMA terminal.
AT&W
OK
AT ＊ DANTE Indicate FOMA terminal reception level in the " ＊ DANTE : <n>" format.
n=0 : Out of service area n=1 : Received signal level of FOMA terminal is 0 or 1 antenna.
n=2 : Received signal level of FOMA terminal is 2 antennas.
n=3 : Received signal level of FOMA terminal is 3 antennas.
AT ＊ DANTE=? : Display a list of displayable values
AT ＊ DANTE
＊
DANTE : 3
OK
AT ＊ DGANSM=<n>
*2
Set to reject or permit incoming packet communications.
n=0 : Reject setting = OFF, Accept setting = OFF (default)
n=1 : Reject setting=ON n=2 : Accept setting=ON
AT ＊ DGANSM? : Display current settings
AT
＊
DGANSM=? : Display a list of assignable values
AT ＊ DGANSM=0
OK
AT ＊ DGAPL=<n> [,<cid>]
*2
Set the dialup connections (APN) to permit incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN permitted for incoming communications
n=1 : Delete from list of APN permitted for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT ＊ DGAPL? : Display current settings
AT ＊ DGAPL=? : Display a list of assignable values
AT ＊ DGAPL=0,1
OK
AT ＊ DGARL=<n> [,<cid>]
*2
Set the dialup connections (APN) to refuse incoming packet communications. APN uses
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN rejected for incoming communications
n=1 : Delete from list of APN rejected for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT ＊ DGARL? : Display current settings
AT
＊
DGARL=? : Display a list of assignable values
AT ＊ DGARL=0,1
OK
AT ＊ DGPIR=<n>
*2
Set Caller ID notification when packet communication connection is being performed. This
command is available when a communication is sent or received.
n=0 : Connect to APN directly (default) n=1 : Connect to APN prefixing 184
n=2 : Connect to APN prefixing 186
When Show/Hide caller ID is specified by dialup network → P17
AT ＊ DGPIR? : Display current settings
AT ＊ DGPIR=? : Display a list of assignable values
AT ＊ DGPIR=0
OK
AT ＊ DRPW
Indicate an index for the reception power of the radio waves that FOMA terminal receive.
AT ＊ DRPW=? : Display a list of displayable values
AT ＊ DRPW
＊ DRPW : 0
OK
AT+CAOC Display last call cost.
AT+CAOC
+CAOC : "000024"
OK
AT+CBC Display FOMA terminal's battery level in the "+CBC : <bcs>,<bcl>" format.
bcs=0 : Powered by the battery pack bcs=1 : Not powered by the battery pack
bcs=2 : Battery pack removed bcs=3 : Power-supply error
bcl=0 : No battery remained or battery pack removed bcl=1-100 : Battery remained
AT+CBC=? : Display a list of displayable values
AT+CBC
+CBC : 0,100
OK
Upper slot : Command
Lower slot : Example
Description