Docomo P-06b, Инструкция по эксплуатации

Страница: 158 / 171

38
AT
¢
DGPIR=n
[M]
This command is valid at dialing/
receiving calls.
In the dial-up network setting,
you can add “186” (notify) or
“184” (not notify) to the phone
number of the access point.
(See page 24) n=0: Uses the APN as it is. (default)
n=1: Adds “184” to the APN. (always not notify)
n=2: Adds “186” to the APN. (always notify)
AT
¢
DGPIR?: Displays the current setting.
AT
¢
DGPIR=0
OK
AT
¢ DGPIR?
¢
DGPIR:0
OK
AT ¢ DRPW
[AT][M]
Displays the output power index
for receiving.
(0: minimum value to 75:
maximum value)
−
AT ¢ DRPW
¢ DRPW:0
OK
+++
[M]
Changes to the online command
state without disconnecting the
line when the escape sequence
is executed in the online mode.
− −
AT+CAOC
[M]
Displays the charging
information for now or latest call. Result: +CAOC:”n”
n: Displays the charging information in a hexadecimal
number.
AT+CAOC
+CAOC:"00001E"
OK
AT+CBC
[M]
Displays the battery level. Result: +CBC:n,m
n=0: FOMA terminal is powered by the battery.
n=1: During charging
n=2: The battery is not connected.
n=3: Power-supply error
m=0
〜
100: Battery level
AT+CBC
+CBC:0,80
OK
AT+CBST=n,1,0
[M]
[&W][&F]
Sets the bearer service to be
used. n=116: 64000 bps (bit transparent) (default)
n=134: 64000 bps (multimedia) AT+CBST=116,1,0
OK
AT+CBST?
+CBST:116,1,0
OK
AT+CDIP=n
[M][AT]
[&F][&W]
Sets whether to display
“Received sub-address” on your
personal computer when you
receive a call. n=0: Does not display “Received sub-address” when
you receive a call. (default)
n=1: Displays “Received sub-address” when you
receive a call.
Result: +CDIP:<n>,<m>
m=0: Not signed up for Multi Number
m=1: Signed up for Multi Number
m=2: Unknown
AT+CDIP=0
OK
AT+CDIP?
+CDIP:0,1
OK
AT+CEER
[AT][M]
Displays the reason why the
preceding call was disconnected. <report>
Disconnection reason list (See page 45) AT+CEER
+CEER:36
OK
AT+CGDCONT
[M]
Sets the access point name
(APN) for when dialing for packet
communication. See page 43. See page 43.
AT+CGEQMIN
[M]
Registers the reference value to
judge whether the system
permits QoS (Quality of service)
reported from the network at
establishment of the packet
communication. AT+CGEQMIN=[parameter]
See page 44.
AT+CGEQMIN=?
Lists the settable values.
AT+CGEQMIN?
Displays the current setting. See page 44.
AT+CGEQREQ
[M]
Sets QoS (Quality of service) to
be requested to the network at
dialing of the packet
communication. AT+CGEQREQ=[parameter]
See page 44.
AT+CGEQREQ=?
Lists the settable values.
AT+CGEQREQ?
Displays the current setting. See page 44.
AT+CGMR
[M]
Displays the version of the
FOMA terminal.
−
AT+CGMR
1234512345123456
OK
AT command Outline Parameter/Explanation
Command execution
example
Continued to Next Pa g e