Docomo FOMA N601i, Руководство пользователя

Страница: 83 / 469

80 Making/Receiving Videophone Calls
d
If a videophone call is not connected
If a videophone call was not connected, a message giving the reason for the connection failure
appears. However, in some circumstances, an explanatory message may not be displayed. Also,
depending on the type of phone used by the callee and the possible lack of a network service
subscription, the reason given may not accurately reflect the callee’s actual status.
e If you make a videophone call to an emergency number (110, 119 or 118) from a FOMA terminal, the call is
automatically changed to a voice call.
e
If you make a videophone call to a phone that does not support videophone call, or if the callee’s phone supports
videophone call but is out of signal range or switched off, no connection can be established. If you called a phone
that does not support videophone call and “Auto redial as voice” (p.84) is set to “ON”, the call is cut off by the called
party before the videophone connection is established and is then automatically redialed as a voice call. However,
this operation is not carried out if you dial a wrong number or if you call an ISDN synchronous 64K or PIAFS access
point or an ISDN videophone that does not conform to the 3G-324M standard (as of November 2006). Note that the
call charge may apply in some cases.
e
The “32K” connection speed allows you to use videophones or other devices (PHS mobiles, etc.) that cannot
communicate at “64K” due to network conditions. If you make a videophone call at “64K” and the called party is in a
“32K” area or similar situation, the call is automatically redialed at 32kbps. However, note that “32K” videophone
calls attract the same digital communication charges as “64K” videophone calls.
e
If “Auto redial as voice” (p.84) is set to “ON” and a videophone call is not connected, the call is automatically
changed to a voice call. The relations between the set connection speed and “Auto redial as voice” setting are
listed below.
e You cannot receive i-mode mail, MessageR or MessageF during a videophone call. Mails you cannot receive are
held at the i-mode Center. Receive them using “Check new messages” after a videophone call ends.
e
You can receive SMS during a videophone call.
e
If the “Recharge battery” low voltage alarm appears on the display during a videophone call, the other party sees
the “Camera Off” message and the call is disconnected roughly 20 seconds later. If you start charging a battery
before a videophone call is terminated, the call continues with the image that had been displayed before the low
voltage alarm was given.
e
Digital call charges still apply when a substitute image appears during a videophone call.
Message Reason
Check number then redial The dialed phone number is currently not used.
Busy* Line is busy.
Packet communication i-mode communication or Packet communication is progress on
the callee.
Out of service area/power off The callee’s phone is out of service or the power is turned off.
Set caller ID to ON Displayed when you connected without notifying your caller ID
(when dialing into visualnet).
Your call is being forwarded The call is being forwarded (into a videophone call if the
forwarding party has a videophone set to comply with 3G-
324M).
Redial using voice call The forwarded party is non-videophone-terminal.
Notify your Caller ID The Caller ID Request service is set on the callee.
The other party does not want to answer your call The called party has set the Bar Nuisance Calls service.
Upper limit has been exceeded. Connection failed. The upper limit set for a Limit billing plan (Type Limit and Family
Wide Limit) is exceeded.
Connection failed Set “Caller ID Notification” to “ON” and then try again.
a
This message may also be displayed in other situations.
* This message may also appear during Packet communication depending on the type of other party’s terminal.
NOTE
Dialing speed set to “64K” Dialing speed set to “32K”
“Auto redial as
voice” set to ON
The connection speed automatically changes to
“32K”. If the videophone call still fails to connect, it
switches to voice-call mode. Switches to voice call mode.
“Auto redial as
voice” set to OFF
The connection speed automatically changes to
“32K”. If the videophone call still fails to connect,
the videophone call ends. Ends the videophone call.