Docomo F960I, Инструкция по эксплуатации

Страница: 183 / 562

181
Mail
･
When you are out of the service area and the number of Auto-send mail is
less than 5, setting confirmation screen for Auto-send appears. When
selecting "Yes", i-mode mail with Auto-send set is saved in "Unsent" folder
of Unsent messages.
✔
INFORMATION
･
When transmission is complete correctly, the i-mode mail is saved in a folder of
Outbox. When the memory space is not enough or when exceeding the savable
number, the unprotected sent mails are overwritten chronologically.
･
When Deco-mail pictogram (Pictogram D) is used, the mail is sent as Deco-mail.
･
When i-mode mail containing pictograms is sent to other company's mobile phones,
the pictograms are automatically converted to similar pictograms on the receivers
terminal. Note that the pictograms may not be displayed correctly on the receiver's
terminal depending on the models and/or functions of the receiver's terminals and
they may be converted to characters or 〓 if there are no applicable pictograms.
･
Under some radio wave conditions, characters are not displayed correctly at the
receiver side.
･
Even when i-mode mail is sent correctly, an error message "Transmission failed." may
appear depending on the signal quality.
･
Saved in "Unsent" folder of Unsent messages when sending failed.
･
Error messages for address unknown etc. may not be received when mails are sent to
addresses other than DoCoMo.
･
When the memory space of Outbox/Unsent messages is not enough or when
exceeding the savable number, i-mode mail cannot be created or sent. Delete
unnecessary i-mode mail and/or SMS from the folder of Unsent messages.
･
To send an i-mode mail using address B of 2in1 as the sender, use WEBmail. → P190
･
When a mail exceeding 10,000 bytes in process of creation is automatically saved due
to other functions being started etc., some part of it may not be saved.
◆
Adding address <Add address>
i-mode mail can be sent to up to 5 addresses at the same time (Simultaneous
sending).
･
There are 3 address types of receivers as below.
: Main receiver
: Other receiver(s) than the main receiver to inform the contents of the mail
: The receiver(s) to inform the contents of the mail without making the mail
address displayed on other receivers' terminals
･
When no receiver addresses are entered in , the mail cannot be sent.
1
On the mail creation screen, place the cursor on the receiver field
and
a e
Select the entry method
･
When selecting "Mail group", go to Step 3.
Changing address type : On the mail creation screen, place the cursor on the
address and
m9 e
Select the address type
Deleting the added address : Place the cursor on the address on the mail
creation screen and
m8 e
"Yes"
2
Select Address type
3
Enter the address
✔
INFORMATION
･
The mail address entered in the address fields of "TO" and "CC" can be seen on the
receiving side. However, it is not displayed with some terminals, devices, mailing
software, etc.
Deco-mail
Creating and sending Deco-mail
You can create Deco-mail by changing the text font size or background color,
inserting a still image shot, Deco-mail picture or Deco-mail pictogram stored by
default in i-mode mail text.
■ Decoration example
･
Deco-mail can be created in two ways : one is entering characters after selecting
a decoration type (
→ P182) and the other is selecting a decoration type after
entering characters ( → P183).
･
Deco-mail of 100 Kbytes or less in size can be sent. Images up to 20 types or up
to 90 Kbytes in total can be attached to the text out of 100 Kbytes. Note that Flash
graphics are up to 2 items.
Font color/Font size
Insert line
Ticker
Word alignment/Insert image/Swing
Background color
Blinking