doble TDR9000 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 454

doble TDR9000 Скачать руководство пользователя страница 93

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

3-23

Monday

, November 26, 2001 1:09 pm

Trip/Close Module

The Trip/Close control function consists of two parts:

• The Trip/Close control module located inside the TDR9000
• The connector, fuses and protection circuits that are part of the

TDR9000 System module.

The Trip/Close module enables the TDR9000 to control the following
tests:

• Trip
• Close
• Trip Free – Standing
• Trip Free – Delay
• Trip Free – Contact 1 Make
• Reclose – Standing
• Reclose – Delay
• O-C-O Standing
• O-C-O Delay
• O-C-O Contact 1 Make

This module operates the circuit breaker under test through the action
of solid-state switches that Trip or Close the circuit breaker and is
polarity-insensitive, so that the user need not know lead polarity.

The TDR9000 can be ordered without the Trip/Close module, however,
all tests need to be triggered externally to the TDR9000 using a push
button or through SCADA.

«
...
91
92
93
94
95
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов