manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 419 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 419

TDR9000

™ 

Circuit Breaker Test System User’s Guide

72A-1898   Rev. A    11/01

I-9

Monday

, November 26, 2001 1:09 pm

AN3: TR3190

™

 Mechanical Interfaces and Other Transducers

Measuring the mechanical displacement and velocity of circuit breaker 
mechanisms vs. time and contact operation is an important analytical 
method.

Many utilities use simple, mechanical 

Tom Edison Toys

 which only 

measure mechanical displacement vs. time as their primary breaker 
timing tool. Many years of TR1 and TR2 experience have taught us much 
about mechanical measurements using the MY transducer, including 
how to successfully interface the transducer to breaker mechanisms. 
Although it is straightforward, it is not quite so simple as it appears. High 
acceleration requires interfaces and transducers with low mass, so as not 
to affect the measurements. High shock loads at the limits of travel 
require rugged interfaces so they don't fall apart, or impart false 
movement due to their mechanical instability. High resolution and 
accuracy are required; none of these characteristics are commercially 
available, so the TR3190 was born.

”AN2: TR3190™ Digital, Linear/Rotary Motion Transducer” on page I-1 
describes the design of the TR3190 Digital, Rotary/Linear Transducer in 
detail and provides insight into the design of adapters/interfaces. It is 
Doble's policy to develop both rotary and linear motion mechanical 
interfaces for the TR3190.

Over the years the client users of TR1/TR2 have also developed interfaces 
and documented many of them. The SFA interface has been developed 
because the OEM slide wire adapters supplied by Westinghouse to 
provide electrical measurements of motion are no longer available.

N

OTE

The T3 Input Expander was an auxiliary instrument designed to 
interface between Westinghouse SFA slide wires and TR2/PR2, and to 
interface to additional MV Transducers for measuring a total of three 
mechanisms, simultaneously. 

Photographs of the interface connected to an SFA breaker module, a 
sketch of the interface form part of this design, will be provided on 
request. 

Other additions include the TR3170 Rotary Transducer and the TR3171 
AHMA-4/8 Transducer. The TR3171 Transducer is used on any circuit 
breaker that uses the AB AHMA-4/8 operator. This includes ABB Type PA 
circuit breakers, certain ELF circuit breakers and PM circuit breakers 
where the voltage class is 345 kV and above.

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов