doble TDR9000 Скачать руководство пользователя страница 32

Страница: 32 / 454

Step 2: TDR9000

™

Connections

1-6

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Step 2: TDR9000

™

Connections

Figure 1.2, Figure 1.3 a nd Figure 1.4 on page 1-8 show the TDR9000
Physical Front Panel wirings for an EHV, OCB/Motion and Event Trigger
test, respectively.

OTE

For First Trip/Close tests complete steps 1 through 4 and then proceed
to ”First Trip/Close Tests” on page 4-1.

To connect the TDR9000:

Remove the front protective cover and store it in a safe place for
reuse.

If the printer option is available, locate the cover/printer assembly
near the laptop.

Plug the ground cable into the system ground receptacle and ground
the other end.

Plug the Safety Switch cable into the

SAFETY

receptacle of the System

module. The Safety Bypass flag is used for First Trip/Close tests.

Ensure that the line voltage is correct (100 - 240 VAC, 50 or
60 cycles).

Connect the female end of the Motion Transducer cable to one of the

MOTION

connectors on the TDR9000 OCB/Motion module, if

present.

Connect the male end of the Motion Transducer cable to the
transducer.

Connect the Breaker Control cable to the

TRIP

CLOSE

connector on

the TDR9000 System module.

Connect either:

• An OCB Contact Monitor cable to the

OCB

connector on the

TDR9000 OCB/Motion module.

• The EHV Contact Monitor cables to the

EHV

connectors on the

TDR9000 EHV modules.

Refer to ”Connecting the TDR9000™ Physical Front Panel”
on page 4-30.

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 32 / 454

Результаты поиска

Содержание TDR9000

Отзывы: