doble TDR9000 Скачать руководство пользователя страница 167 | Manualshive

Страница: 167 / 454

doble TDR9000 Скачать руководство пользователя страница 167

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-69

Monday

, November 26, 2001 1:09 pm

Running Tests

This section explains the procedures involved in running tests and saving
Test Results to disk. These include:

• Removing Safety Grounds
• Using the Pretest Checklist
• Running the Continuity Test
• Running Other tests
• Saving Test Results for importation to the back office server

running TRX

• Disconnecting after the test is complete

Removing Safety Grounds

Before the test can be run, ground connections must be removed from
either side of the circuit breaker. Certain electrical/physical conditions,
however, may dictate which safety grounds can safely be removed. Refer
to the warning below.

W

ARNING

If the circuit breaker is closely connected to a transformer (there is
no disconnect switch between the transformer and the circuit breaker)
whose neutral is grounded, the safety grounds that remain must be the
ones between the transformer and the circuit breaker.

If there is high voltage between one side of the circuit breaker and the
closest isolating disconnect switch, the safety grounds that remain must
be on the long section of the high-voltage bus.

«
...
165
166
167
168
169
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов