doble TDR9000 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 454

doble TDR9000 Скачать руководство пользователя страница 137

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-39

Monday

, November 26, 2001 1:09 pm

Configuring Test Plans

There are two types of Test Plans:

• Library Test Plan
• Breaker Test Plan

A Library Test Plan contains the information required to run a general test
on a breaker type. This plan is flexible, in that none of the nameplate
information stored in this format is specific to a particular circuit breaker.
The Library Test Plan can be used repeatedly as a basis for configuring
multiple tests with the same basic test configuration, and on circuit
breakers of the same type.

A Breaker Test Plan is created when any circuit breaker-specific
information is entered in the nameplate on the

Test Plan

tab. Once such

information is entered, the title on top of the

Test

Plan

tab changes from

Library Test Plan

to

Breaker Test Plan

. This occurs by entering

information into

any

of the following fields:

• Manufacturer
• Serial Number
• Location
• Special ID

Both Test Plan types minimize the time required to configure tests as they
store common circuit breaker testing information and test parameters.
Items that can comprise a Test Plan include:

• Circuit breaker ID, such as type, serial number and manufacturer
• Range selection for Trip/Close currents
• Circuit breaker specifications and measurement zones, as

specified by the manufacturer

• Units of measurement (seconds or cycles, English or Metric)
• Transfer function for motion measurements
• Channel activation
• Performance specifications

N

OTE

The TDR9000 can be used in either the 50 or 60 Hz environment. This
selection is made using the TRX Options window accessed from the
TRXField View pulldown menu. For a complete description of this
window, refer to page A-31.

The TRXField software opens with the

TRXField for TR3000 and

TDR9000

dialog box open (Figure 4.15).

«
...
135
136
137
138
139
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов