doble TDR9000 Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 454

doble TDR9000 Скачать руководство пользователя страница 130

Connecting the TDR9000

™

Physical Front Panel

4-32

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

9.

Connect the:

a.

Trip

leads across the terminals of the manual Trip switch on

the circuit breaker control panel.

b.

Close

leads across the terminals of the manual Close switch

on the circuit breaker control panel (local connection
schemes may vary).

If the manual trip switch connections are inaccessible:

• connect between the +DC voltage supply of the terminal strip

to the input side of the trip coil.

This configuration also serves for close coil operations.
Either method, across the switch or using the coils makes
the TDR9000 a series switch that aDC voltage to the
appropriate coil for operation.

10.

Taking appropriate safety precautions, use the attachment accessories
provided to connect an:

• OCB Contact Monitor cable to the

OCB

connector on the

TDR9000 OCB/Motion module and then to the appropriate
circuit breaker bushings.

See

A

in Figure 4.13 on page 4-30. Connect alligator clip leads as

labeled, A,B,C Common or 1,2,3 Common.

or

• EHV Contact Monitor cables to the

EHV

connectors on the

TDR9000 EHV module and then to the appropriate circuit
breaker bushings.

See

C

in Figure 4.13 on page 4-30. Connect alligator clip leads as

labeled PH A, Contact 1,2, Common, etc.

Analog and
Auxiliary Setup

Setup issues for the Event module include:

• Monitoring Auxiliary Channels
• Monitoring Analog Channels: Current and Voltage

Monitoring
Auxiliary
Channels

The TDR9000 Auxiliary Contact channels support inputs from external
devices. Auxiliary Contacts can be wetted with voltages from 48 to 300 V
peak. Configuration is performed using the

Auxiliary Contact Connector

or the

Auxiliary Contacts

dialog box of the Virtual Front Panel. Refer to

”Configuring the Event Module” on page 4-51.

«
...
128
129
130
131
132
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов