doble TDR9000 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 454

doble TDR9000 Скачать руководство пользователя страница 123

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-25

Monday

, November 26, 2001 1:09 pm

Configuring the TDR9000

™

With the field-side connections complete, the laptop running TRXField is
connected and the Virtual Front Panel is configured.

Once the TDR9000 is powered up and a Test Plan is selected or
configured, the Virtual Front Panel displays all the active channels
included in that Test Plan. Channels active in the Test Plan appear on the
Virtual Front Panel according to a color scheme that indicates their
readiness to start (refer to ”Connector Indications” on page 3-9) and acts
as an aid to personnel in completing all required connections. Refer to
”Basic Virtual Front Panel Functionality” on page 3-5.

Each time a test is run, different values can be configured on different
modules. A general procedure for the tasks required to configure the
TDR9000 Virtual Front Panel follows. After each step, a cross reference
leads to the specific discussion of that topic. Once all required tasks from
this general procedure are complete, the test is run.

Configuring the TDR9000

™

: General Procedure

To configure the TDR9000:

1.

Connect the laptop to the serial port of the TDR9000, power up the
laptop and the TDR9000, and run the TRXField software.

If necessary, refer to ”Connecting to the Laptop, Printer and Powering
Up” on page 4-27.

The TRXField software on the laptop determines what version of the
firmware is resident on the TDR9000. If the versions do not match, a
dialog box appears asking for permission to download the laptop
version to the TDR9000 firmware. If permission is given, the process
takes approximately five minutes. A status bar appears on the laptop
to monitor download progress.

The download can be cancelled by clicking

Cancel

.

N

OTE

If the download is cancelled or not done, the TDR9000 becomes
inaccessible.

2.

Connect the TDR9000 Physical Front Panel. Refer to page 4-30

«
...
121
122
123
124
125
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов