DLS T20 TWEETER
Speaker connection and tweeter level
select:
The cable filters coming with this tweeter (when bought as a
tune-up speaker) should be connected in series with
respective speaker element as on the drawing. Select
tweeter level using the red or yellow cable coming out from
the cable filter. If the tweeter is directed towards the listener,
low level is to be prefered. Otherwise make your own tests
for best result.
Sometimes the midrange can be improved by phase
reversing the tweeter. Try it and judge yourself. The
tweeter level select in PS and REFERENCE is made iside
the black filter box by moving a small jumper.
NOTE! Filters must be used. If the tweeters are
connected without filters they will be damaged and
sound reproduction becomes bad.
THE KIT CONTAINS:
2 pcs 20 mm / 0,79"swivelball head tweeters
Mounting accessories for dash-
and recessed mounting
FILTER CONNECTION
T20 connected to any other speaker
system:
A separate tweeter filter must be used. This cable filter
(art.no 9-25604) is only included when T20 is bought as
a tune-up speaker for other systems.
Thank you for buying DLS T20 tweeters. The T20 tweeters are
included in some models of the CLASSIC and REFERENCE series
speaker kits.
They can also be bought separately for use as "Tune-up
speakers" to improve the treble in any other system.
DLS Svenska AB
P.O. Box 13029
SE-402 51 Göteborg, Sweden
Tel. +46 31 840060
Fax +46 31 844021
E-mail: [email protected]
www.dls.se
If you have any questions about this product, contact
your local dealer or DLS customer support center.
Size
20 mm / 0,79"
Nom. power (RMS)
50 Watts, 80 Watts max
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
X-over frequency
3,5 kHz with cable filter 9-25604
Magnet diameter
20 mm / 0,79"
Mounting depth
20 mm / 0,78" (recessed mounting)
Mounting hole
48 mm / 1,89" (recessed mounting)
Cone material
Silk
FACTS ABOUT DLS T20 TWEETER
MOUNTING:
T20 can be mounted on the dashboard with the plain cup (1), the
angled cup (2), or recessed in a doorside.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○
Red +
Car stereo / amplifier
Black -
Blue +
Black -
Red +
Tweeter T20
Bass/mid
Black -
Low-pass filter
(if used)
Yellow
Speaker
impedance 4
Ω
Tweeter level select:
Red to red = high
Red to yellow = low
Tweeter filter
9-25604
Red
INPUT WOOFER TWEETER
+
-
+
-
+
-
Bass/mid
Tweeter
Car stereo /
amplifier
T20 connected to a PRO slimline or REFERENCE
2-way system.
T20 connected to CLASSIC C4, C5 or C6.
Connect as in the drawing below. The cable filters are
different for each model. The article numbers are:
For C4: 9-25605, C5: 9-25606, C6: 9-25610.
SURFACE MOUNTING:
Plain mounting: Use only the plain mounting cup 1, (it´s normally
mounted at delivery). Attach to surface with the two screws or
double adhesive tape.
Angled mounting
:
Remove the plain mounting cup by bending with
a small screw driver in the gap (A). Attach the tweeter element to
the angled cup (2) as shown on picture 3. Pull the cable through
the center hole. Now the tweeter can be mounted in two different
angles. Attach to the surface with the two screws or double
adhesive tape.
A
2
1
3
DLS Svenska AB 03-05-19
RECESSED MOUNTING:
Drill a hole in the door side with a diameter of 48 mm /1,89". The in-
stallation becomes easier if the door side is removed from the door.
Remove the tweeter element from the plain mounting cup by ben-
ding with a small screw driver in the gap ( A). Put the two metal
wings through the two tracks in the center of the cup, just as the
picture shows, and attach them with the M4 screw and nut through
the center hole. Attach the tweeter element to the plain cup using
the mounting ring (C). The metal wings (B) should be on the back
side of the door panel, holding the cup in place.
B
C
A
