background image

How to install and operate the 

DLS amplifier models

Welcome!

This owners manual is written in easy english and
uses a lot of drawings to simply the installation and 
use of the above amplifiers.

Your DLS amplifiers must be installed correctly in 
order to work well. This manual will show you how 
to install the amplifier like a pro. Please read the 
entire manual before beginning the  installation.
Install the amplifier yourself if you feel confident  
with our instructions and if you have the proper tools. 
However if you feel unsure, turn over the installation 
job to someone better suited to it.

Warranty Service

This amplifier is covered by warranty, depending on 
the conditions in the country where it is sold. If the 
amplifier is returned for service, please include the 
original dated receipt with the product.

Contents

Features……………………………..............   2
Installation…………………….…….............   2
Routing Wires……………………................   2
Tools and materials needed……….............   3

Wiring & crossovers:

Power and remote wiring............................. 3-4
Low & High level input wiring ......................   4
Input level control, BASS EQ, etc ...............   5
Features on each model .............................   5

 
CC-500 speaker wiring:

One or more subwoofers...............................  6

CC-2 speaker wiring:

Front speakers…...………………................   7
Subwoofer…………………………...............   7

CC-4 speaker wiring:

Four speakers……………………................   8
Two speakers and bridged subwoofer........   8
Two subwoofers or a stereo speaker pair
connected in bridge mode .........................   9

Testing………………………………............     10
Troubleshooting……………………............     10    
Professional tips………………….........…..      11
Specifications………………………............     12

Technical Assistance

For technical assistance ask the shop where the 
product was sold or the distributor in your very 
country. Information can also be found on our WEB-
site www.dls.se
We follow a policy of continuous advancement in 
development. For this reason all or part of specifica-
tions & designs may be changed without prior notice.

DLS Svenska AB

P.O. Box 13029 - SE-40251 Göteborg - Sweden

Tel: +46 31 840060 - Fax: +46 31 844021

E-mail: [email protected]

www.dls.se

DLS amplifiers are designed and engineered by:

This product must be returned to the 
separate collection system for electronic 
products. Do not dispose this product 
together with general household waste.

DECLARATION OF CONFORMITY

DLS amplifiers for vehicles are manufactured in 
accordance with the EU directive EEC 95/54 (72/245/
EEC) and are marked with the approval number. 
They are also marked in accordance with the WEEE-
directive 2002/96/EC.
The products are also produced in accordance with 
the EU RoHS directive 2002/95/EC.

CC-2
CC-4

CC-500

Sound tuned in England.

Содержание CC-2













Отзывы: