DKS 6400 - UL 325 Class 1 Скачать руководство пользователя страница 14

Страница: 14 / 22

6400-065-T-8-12

The drive motor orientation determines the opening direction of the gate.

It may need to be unbolted and flipped 180° to allow

the gate to open in a specific direction. Limit assemblies will need to be moved accordingly.

LIMIT ASSEMBLIES are factory set

to open the gate counter-clockwise.

Note: Drive arm and

linking arm are shown in

“OPEN”

gate position.

Limit assemblies are factory set in the

“Open counter-clockwise” position.

Drive motors face the same direction in a dual gate installation.

Limit assemblies are positioned according to the opening direction of the gate (See limit plates

and

shown above).

Drive Motor Orientation and Components Installation

Dual Gate Operators

Drive

Arm

Drive

Motor

Limit assemblies must be slid 90° clockwise on limit
plate to be in the correct “Open clockwise” position.

Note:

“Precise Final” limit

adjustments will be made
when wiring the operator.

See the selected control box

“Wiring/Owner’s” manual.

Open
Gate

Gate

Drive
Arm

Limit
Plate

Limit Plate

Open Limit

Assembly Position

(4 Slo Dwn) Purple/White

(3 Limit) Gray/White

Close Limit Assembly

Position

Purple/White (4 Slo Dwn)

Gray/White (3 Limit)

Close Limit Assembly

Position

Brown/White (6 Slo Dwn)

Yellow/White (5 Limit)

Open Limit

Assembly Position

Brown/White (6 Slo Dwn)
Yellow/White (5 Limit)

Limit
Plate

Drive

Motor

Linking Arm

Link

Open

Gate

Open Counter-Clockwise

Open Clockwise

Drive

Arm

Drive

Motor

Open

Gate

Drive

Arm

Drive

Motor

Open

Gate

Primary Operator

Open Counter-Clockwise

Secondary Operator

Open Clockwise

Secondary Operator

Open Counter-Clockwise

Primary Operator

Open Clockwise

Drive

Arm

Drive

Motor

Open

Gate

Drive

Arm

Drive

Motor

Open

Gate

Содержание 6400 - UL 325 Class 1























Результаты поиска

Содержание 6400 - UL 325 Class 1

Отзывы:

DKS 6400 - UL 325 Class 1, Руководство пользователя, Страница: 14 / 22

Результаты поиска

Содержание 6400 - UL 325 Class 1

Отзывы: