Dixon SPEEDZTR 42SE Скачать руководство пользователя страница 53

Страница: 53 / 60

seRVICe JoURnal

action

Date, mtr reading, stamp, sign

Delivery Service

Charge the battery

Adjust the tire pressure of all wheels to 15 PSI (1 bar)

mount the steering controls in the normal position

Connect the contact box to the cable for the seat’s safety switch

Check that the right amount of oil is in the engine

Adjust the position of the steering controls

fill with fuel and open the fuel shut off valve

Start the engine

Check that there is drive to both wheels

Check the mower deck adjustment

Check:

Safety switch for the parking brake

Safety switch for the mower deck

Safety switch in the seat

Safety switch in the steering controls

Parking brake functionality

Driving forward

Driving backward

engaging the blades

Check the idle speed

Check the engine high idle speed

Inform the customer about:

Need and advantages of following the service schedule

Need and advantages of leaving the machine for service every 300 hours

effects of service and maintaining a service journal on the machine’s

resale value

Application areas for mulching

fill in the sales papers, etc.

Delivery service has
been carried out
No remaining notes
Certified:

Содержание SPEEDZTR 42SE





























































Результаты поиска

Содержание SPEEDZTR 42SE

Отзывы:

Похожие инструкции для SPEEDZTR 42SE

Бренды по названию

Популярные бренды

Dixon SPEEDZTR 42SE, Руководство оператора

Результаты поиска

Содержание SPEEDZTR 42SE

Отзывы:

Похожие инструкции для SPEEDZTR 42SE

Бренды по названию

Популярные бренды