Dixon SPEEDZTR 42SE Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 60

background image

31

opeRatIon

Operating On Hills

Read the Safety Instructions

Driving on Slopes

in the

Safety

section.

• The slowest speed possible should be used

before starting up or down hills.

• Avoid stopping or changing speed on hills.
• If stopping is absolutely necessary, pull steering

controls into the neutral position and push to the
outside of the unit. engage the parking brake.

8058-213

Parking brake released

WARNING!

Do not drive up or down hills with slopes
greater than 10 degrees. Do not drive
across slopes.

8058-190

Place controls in neutral position

• To restart movement, release the parking brake.
• Pull the control levers back to the center of the

mower and press forward to regain forward
motion.

• make all turns slowly.

«
...
29
30
31
32
33
...
»

Содержание SPEEDZTR 42SE





























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDZTR 42SE

Бренд: AL-KO Страницы: 116

Бренд: Gardenline Страницы: 30

Бренд: Baroness Страницы: 66

Бренд: SaMASZ Страницы: 22

Sweep It 23630YW

Бренд: Yardwise Страницы: 8

Бренд: Sabo Страницы: 100

Бренд: IHI Shibaura Страницы: 51

Бренд: Kubota Страницы: 59

Бренд: VITO GARDEN Страницы: 20

Бренд: Hayter Страницы: 36

Бренд: OHIOSTEEL Страницы: 14

Бренд: Wards Garden Mark Страницы: 4

Бренд: Wards Garden Mark Страницы: 16

Бренд: EMAK Страницы: 120

Бренд: Gardena Страницы: 152

Бренд: Gardena Страницы: 14

Бренд: Toro Страницы: 24

Бренд: Toro Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды