Dixon SPEEDZTR 42SE Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 60

background image

26

opeRatIon

Starting the Engine

1. Sit on the seat.
2. Raise the mower deck by pushing the release

button on the top of the lifting lever. Pull the lifting
lever backward to the locked (transport) position.

3. Activate the parking brake by pushing the release

button in and pulling the lever fully upwards.

4. Disengage the mower blades by pressing the

blade switch downwards.

8058-256

Mower deck lifting lever

8058-134

Blade switch

8058-213

Pull parking brake upwards to activate.

«
...
24
25
26
27
28
...
»

Содержание SPEEDZTR 42SE





























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDZTR 42SE

Бренд: MTD Страницы: 16

Бренд: Harrier Страницы: 33

Бренд: Poulan Pro Страницы: 48

Бренд: Toro Страницы: 28

Бренд: Troy-Bilt Страницы: 72

Бренд: Cub Cadet Страницы: 24

Бренд: Wards Garden Mark Страницы: 12

Бренд: Yardworks Страницы: 40

Бренд: Yard-Man Страницы: 8

Бренд: Yard-Man Страницы: 16

Бренд: Yard Machines Страницы: 12

Бренд: Yard Machines Страницы: 24

Бренд: Yard force Страницы: 50

Бренд: Yard force Страницы: 76

Бренд: Yard force Страницы: 98

Бренд: Yazoo Страницы: 8

Бренд: Spearhead Страницы: 30

Бренд: Spearhead Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды