Dixon GRIZZLY SE 6029FX Скачать руководство пользователя страница 45

Страница: 45 / 72

maINTeNaNCe

Pump Belt

The belts are not adjustable. Replace belts if they
begin to slip from wear.

Replacing Pump Belt

Park the mower on a level surface. Engage the
parking brake.

Belt Removal

Remove the deck belt (see

Deck Belt Removal

in this section of the manual).
Remove clutch stop to access the belt.

Disconnect clutch wire.

With a ½" breaker bar and using the square

opening in the idler arm, shift the arm to create
slack in the belt.
Remove belt from the engine and pump pulleys.

Belt Installation

Wrap the belt around the engine pulley.

Wrap the belt around the left pump pulley.

Route the belt around the inside of the idler

pulley.
With a ½" breaker bar and using the square

opening in the idler arm, shift the arm to create
slack in the belt.
While holding the idler back with the breaker
bar, wrap the belt around the right pump pulley.
Replace and secure clutch stop.

Reinstall the deck belt. (See

Deck Belt

Installation

in this section of the manual).

8065-041

Electric clutch
Idler arm release placement
Clutch stop

Pump belt removal

V-belts

Check every 100 hours of operation. Check for severe
cracking and large nicks.
NoTE: The belt will show some small cracks in normal
operation.

Double check belt routing to make sure it

matches the routing decal, and that the belt
does not have any twist. Correct if needed.
Adjust belt tension by turning the eyebolt until

there is approximately

" -1" of threads showing

outside the nut.
Belt tension should be set to 60-70 lbs.

Replace belt shields on both mandrel housings

and secure with fasteners.

8065-054

Adjust belt tension

Содержание GRIZZLY SE 6029FX









































































Результаты поиска

Содержание GRIZZLY SE 6029FX

Отзывы:

Похожие инструкции для GRIZZLY SE 6029FX

Бренды по названию

Популярные бренды

Dixon GRIZZLY SE 6029FX, Руководство оператора

Результаты поиска

Содержание GRIZZLY SE 6029FX

Отзывы:

Похожие инструкции для GRIZZLY SE 6029FX

Бренды по названию

Популярные бренды