Dixon 27 KOH/968999588 Скачать руководство пользователя страница 7

Страница: 7 / 88

English

SYMBOLS AND DECALS

These symbols are found on the machine and in the operator’s manual.

Study them carefully so that you know what they mean.

Used in this publication to notify the reader of a risk of

personal injury or death

, particularly if the reader should

neglect to follow instructions given in the manual.

Used in this publication to notify the reader of a risk of

material damage

, particularly if the reader should neglect

to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.

WARNING!

Xxxx xxxxxx xxxxx xxxx
xxxxxxxxx xxxxxx xxxxxxxxx.
xx xxxxxxxx xxxx xxxxxx

IMPORTANT INFORMATION

Xxxx xxxxxx xxxxx xxxx xxxxxxxxx
xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx
xxxxxx

Reverse

Neutral

Fast

Slow

Choke

Fuel

Warning!

Parking Brake

CE conformity

Warning! Rotating blades,

Do not touch parts

marking. Only for

keep away from the

European market

discharge deck

Battery acid is corrosive, explosive and fl ammable

Do not stand here

Noise emissions to the
surroundings in accordance with
the European Union’s directive.
The machine’s emission is stated
in the chapter TECHNICAL DATA
and on the decals.

Only machines for European
market

Use protective glasses

Use protective gloves

Содержание 27 KOH/968999588

























































































Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды

Dixon 27 KOH/968999588, Руководство оператора

Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды