Dixon 27 KOH/968999588 Скачать руководство пользователя страница 64

Страница: 64 / 88

English

TROUBLE SHOOTING GUIDE

The engine seems weak.

•

Clogged air fi lter.

•

Defective spark plugs.

•

Carburetor incorrectly adjusted.

•

Air trapped in hydraulic system.

The engine overheats.

•

Clogged air intake or cooling fi ns.

•

Engine overloaded.

•

Poor ventilation around engine.

•

Defective engine speed regulator.

•

Soot in the combustion chamber.

•

Too little or no oil in the engine.

•

Defective spark plugs.

•

Pre-ignition incorrect.

•

Air trapped in hydraulic system.

Battery not charging.

•

Poor contact with battery terminal cable
connectors.

The machine moves slowly, unevenly, or not at all.

•

Parking brake on.

•

Bypass valve on pump open.

•

Drive belt for the transmission gears slack or has
come off.

•

Air trapped in hydraulic system.

Mower deck not engaging.

•

Drive belt for the mower deck has come loose.

•

Contact for the electromagnetic coupling has
loosened.

•

The blade switch is faulty or has come loose,
from the cable contact.

•

The fuse has blown.

Transaxle leaks oil.

•

Damaged seals, housing, or gaskets.

•

Air trapped in hydraulic system.

Содержание 27 KOH/968999588

























































































Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды

Dixon 27 KOH/968999588, Руководство оператора

Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды