Dixon 27 KOH/968999588 Скачать руководство пользователя страница 55

Страница: 55 / 88

English

LUBRICATION

Lubrication

Lubrication Schedule

8011-672-2

General

Remove the ignition key to prevent unintentional movements during lubrication.

When lubricating with an oil can, it must be fi lled with engine oil.

When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.

For daily use, the machine should be lubricated twice weekly.

Wipe away excess grease after lubrication.

It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen,
attempt to clean them with spirits. If the belt continues to slip after cleaning, it must be replaced. Gasoline or other

petroleum products must not be used to clean belts.

12/12 Every year

1/52 Every Week

1/365 Every day

Lubricate with grease gun

Oil change

Filter change

Lubricate with oil can

Level check

*Change hydraulic (transmission) fi lters.

Содержание 27 KOH/968999588

























































































Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды

Dixon 27 KOH/968999588, Руководство оператора

Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды