Dixon 27 KOH/968999588 Скачать руководство пользователя страница 50

Страница: 50 / 88

English

MAINTENANCE

Checking the Blades

In order to attain the best mowing effect, it is important
that the blades are well sharpened and not damaged.

WARNING!

Blades are sharp. Protect your
hands with gloves and/or wrap
blades with a heavy cloth when
handling.

Bent or cracked blades or blades with large nicks
should be replaced.

Damaged blades should be replaced when hitting
obstacles that result in a breakdown. Let the service
workshop decide whether the blade can be repaired/
ground or must be replaced.

Balance the blades after sharpening.

Check the blade mounts.

IMPORTANT INFORMATION

The sharpening of blades should be
carried out by an authorized service
workshop.

8011-604

Check the blades

Содержание 27 KOH/968999588

























































































Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды

Dixon 27 KOH/968999588, Руководство оператора

Результаты поиска

Содержание 27 KOH/968999588

Отзывы:

Похожие инструкции для 27 KOH/968999588

Бренды по названию

Популярные бренды