Dixon 12881-106 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 56

background image

CARE AND MAINTENANCE

42

HYDROSTATIC PUMPS:

Before each use, check to be sure that the cooling fins
of the hydrostatic pumps are clean. Excessive
accumulation of oil, dirt, or trash may cause the pumps
to overheat.

NEVER WASH ACROSS TOP OF

RESERVOIR WITH WATER OR STEAM. Fill reservoir
as required per the maintenance schedule listed in this
book.

HYDROSTAT DRIVE BELT REPLACEMENT

PROCEDURE:

To remove hydrostat pump drive belt:

(The hydrostat pump drive is equipped with a spring
loaded belt take-up).

1. Raise seat.
2. Remove hold down bolts from belt cover. Remove

belt cover.

3. Rotate the spring loaded take-up idler towards the

left hand hydro pump to provide belt slack for
removal.

4. Remove belt.

To install hydrostat pump drive belt:

1. Rotate the spring loaded take-up idler

towards the left hand hydro pump.

2. Install belt per diagram.
3. Re-attach belt cover.
4. Return the seat to the

operating position.

«
...
40
41
42
43
44
...
»

Содержание 12881-106

























































Отзывы:

Нет отзывов

Похожие инструкции для 12881-106

Бренд: Mac allister Страницы: 24

Бренд: Yard-Man Страницы: 12

Бренд: Grasshopper Страницы: 56

Бренд: Rally Страницы: 24

Throw Reel Mower

Бренд: Mclane Страницы: 16

Бренд: Ranger Страницы: 38

Бренд: AL-KO Страницы: 25

Бренд: SaMASZ Страницы: 37

Бренд: Poulan Pro Страницы: 17

28HP Tank 53AB5JEZ630

Бренд: Cub Cadet Страницы: 36

Бренд: Cramer Страницы: 184

Бренд: Craftsman Страницы: 8

Бренд: Kraftixx Страницы: 246

Бренд: FXA Страницы: 65

Бренд: FUXTEC Страницы: 18

Бренд: FUXTEC Страницы: 51

Бренд: EMAK Страницы: 24

Бренд: EMAK Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды