Ditch Witch ST37x Скачать руководство пользователя

Страница: 61 / 112

Trench - 60

ST37x Operator’s Manual

Trench

Breathing crystalline silica dust. may cause lung disease.

Cutting, drilling, or working materials such as concrete, sand, or rock
containing quartz may result in exposure to silica dust. Use dust control
methods or appropriate breathing protection when exposed to silica dust.

270-4952

Electrical shock. Contacting electrical lines will cause death or serious

injury. Know location of lines and stay away.

To help avoid injury:

Expose lines by hand before digging. Cutting high voltage cable can cause

electrocution.

Read operator’s manual. Know how to use all controls.

Your safety is at stake.

273-475

To help avoid injury:

•

Comply with all utility notification regulations before digging or drilling.

•

Notify companies that do not subscribe to One-Call.

Flying objects thrown by machine may strike people.

Wear hard hat and safety glasses.

275-193

Moving digging teeth will cause death or serious injury.

Stay away.

275-097

To help avoid injury:

•

Ensure parking brake is engaged.

•

Allow 3’ (1 m) between digging teeth and obstacle. Machine might jerk when digging starts.

•

Keep everyone at least 6’ (2 m) from machine, attachments, and their range of movement.

6ft/2m

Содержание ST37x

















































































































Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды

Ditch Witch ST37x, Руководство оператора

Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды