Ditch Witch ST37x Скачать руководство пользователя

Страница: 52 / 112

ST37x Operator’s Manual

Transport - 51

Haul

Load

Disengage parking brake.

Start engine.

Adjust throttle to low speed.

Pull boom lift control to raise boom clear of trailer, but keep it low.

Move unit to rear of trailer and align with ramps.

Drive forward slowly to move unit onto trailer until tiedown position is reached.

Push boom lift control to lower boom to trailer bed.

Engage parking brake.

Ensure that all controls are in neutral position.

10. Turn ignition switch to STOP.

11. Tie down unit.

Crushing weight. If load falls or moves it could kill or crush

you. Use proper procedures and equipment or stay away.

To help avoid injury:

•

Load and unload trailer on level ground.

•

Incorrect loading can cause trailer swaying.

•

Attach trailer to vehicle before loading or unloading.

•

Only operate unit from operator platform.

•

To help prevent trailer sway, load trailer so that ten to fifteen percent of total vehicle weight
(equipment plus trailer) is on tongue.

•

If loading onto tilt-bed trailer, be prepared for trailer to tilt.

•

Move all controls to neutral position when stopped.

Содержание ST37x

















































































































Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды

Ditch Witch ST37x, Руководство оператора

Результаты поиска

Содержание ST37x

Отзывы:

Похожие инструкции для ST37x

Бренды по названию

Популярные бренды