Ditch Witch SK650 Скачать руководство пользователя страница 63

Страница: 63 / 83

Service - 62

SK650 Operator’s Manual

100 Hour

CMW

100 Hour

Clean Fuel Filter Element

Use kerosene to rinse the filter cup and filter
element every 100 hours. Bleed the fuel system
after cleaning the filter.

See Kubota engine operator’s manual for more
information on cleaning the fuel filter.

Check Fan Belt for Tension and
Damage

Check belt tension every 100 hours. Belt is
properly tensioned when it moves about 1/4-3/8”
(7-9 mm) when pushed at the long span. Replace
the belt when it is worn and sinks into the pulley
groove.

Adjust Tension

Loosen two alternator bolts (shown).

Adjust position as needed.

Tighten bolts.

Check tension.

Location

Task

Notes

Traction Unit

Clean fuel filter element

Check fan belt tension and damage

1/4-1/3” (7-9 mm)

Lubricate parking brake

MPG

Check battery electrolyte level

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды