Ditch Witch SK650 Скачать руководство пользователя страница 36

Страница: 36 / 83

SK650 Operator’s Manual

Prepare - 35

Connect Attachment

CMW

Connect Attachment

Attachment

Position attachment on level surface with enough
space behind it to accommodate unit.

Ensure that lock pin handles (shown) on mount
plate are turned away from center of attachment.

Start engine.

Tilt mount plate (2) forward.

Position mount plate in the upper lip of the receiver
plate (1) on attachment.

Raise lift arms while tilting back mount plate.

Turn ignition switch off and remove key.

Rotate lock pin handles toward center of mount plate
to secure attachment to lift plate.

IMPORTANT:

Use only Ditch Witch-approved attachments. Attachments can change the stability and

operating characteristics of the unit.

IMPORTANT:

Before connecting attachment to unit,

ensure that mount and receiver plates are free of dirt
and debris.

IMPORTANT:

Attachment should be raised

enough to clear the ground. Mount plate
should be tilted back fully.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

NOTICE:

To ensure proper connection, verify that bottoms of lock pins are visible under

attachment receiver plate (shown).

t05om022c.eps

t05om026c.eps

t05om027c.eps

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды