Ditch Witch SK650 Скачать руководство пользователя страница 35

Страница: 35 / 83

Prepare - 34

SK650 Operator’s Manual

Check Supplies and Prepare Equipment

CMW

Check Supplies and Prepare Equipment

Supplies

•

fuel

•

keys

•

lubricants

•

personal protective equipment, such as hard hat and safety glasses

Fluid Levels

•

fuel

•

hydraulic fluid

•

battery charge

•

engine oil

Condition and Function

•

parking brake pins (See “Check Brake Operation” on page 57.)

•

filters (air, oil, hydraulic)

•

tracks

•

pumps and motors

•

hoses and valves

•

signs, guards, and shields

Accessories

Fire Extinguisher

If required, mount a fire extinguisher near the power unit but away from possible points of ignition. The fire
extinguisher should always be classified for both oil and electric fires. It should meet legal and regulatory
requirements.

NOTICE:

Use low sulfur or ultra low sulfur fuel only.

NOTICE:

Use low sulfur or ultra low sulfur fuel only.

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды