Ditch Witch SK650 Скачать руководство пользователя страница 32

Страница: 32 / 83

SK650 Operator’s Manual

Prepare - 31

Inspect Site

CMW

Inspect Site

Inspect jobsite before transporting equipment. Check for the following:

•

changes in elevation such as hills or other open trenches

•

obstacles such as buildings, railroad crossings, or streams

•

signs of utilities (See “Inspect Jobsite” on page 32.)

•

traffic

•

access

•

soil type and condition

Identify Hazards

Identify safety hazards and classify jobsite if attachment will penetrate ground. See “Classify Jobsite” on
page 32.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

NOTICE:

•

Wear personal protective equipment including hard hat, safety eye wear, and hearing protection.

•

Do not wear jewelry or loose clothing.

•

Notify One-Call and companies which do not subscribe to One-Call.

•

Comply with all utility notification regulations before digging or drilling.

•

Verify location of previously marked underground hazards.

•

Mark jobsite clearly and keep spectators away.

Remember, jobsite is classified by hazards in place -- not by line being installed.

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды