Ditch Witch SK650 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 83

background image

Safety - 12

SK650 Operator’s Manual

Guidelines

CMW

Guidelines

Follow these guidelines before operating any jobsite equipment:

•

Complete proper training and read operator’s manual before using equipment.

•

Contact your local One-Call (811 in USA) or the One-Call referral number (888-258-0808 in USA and
Canada) to have underground utilities located before digging. Also contact any utilities that do not
participate in the One-Call service.

•

Classify jobsite based on its hazards and use correct tools and machinery, safety equipment, and work
methods for jobsite.

•

Mark jobsite clearly and keep spectators away.

•

Wear personal protective equipment.

•

Review jobsite hazards, safety and emergency procedures, and individual responsibilities with all
personnel before work begins. Safety videos are available from your Ditch Witch dealer.

•

Replace missing or damaged safety shields and safety signs.

•

Use equipment carefully. Stop operation and investigate anything that does not look or feel right.

•

Do not operate unit where flammable gas is present.

•

Contact your Ditch Witch dealer if you have any question about operation, maintenance, or equipment
use.

«
...
11
12
13
14
15
...
»

Содержание SK650




















































































Отзывы:

Нет отзывов

Похожие инструкции для SK650

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды