Ditch Witch JT5 Скачать руководство пользователя страница 110

Страница: 110 / 155

JT5 Operator’s Manual

Systems and Equipment - 109

Drill Pipe

CMW

Drill Pipe

Perform Regular Drill Pipe Care

Precondition New Pipe

Repeat this procedure

three times

for each piece of pipe before it is used the first time:

Hand-lubricate

entire surface of threads and shoulders of both ends of pipe with copper base tool

joint compound. See page 122 for correct lubricant.

Join pipe and tighten joint.

Break joint.

Move pipe back to box.

Lubricate Joints Before Each Use

Lubricate threads and shoulders of male joints with copper base tool joint compound. This prevents rust
and reduces wear on shoulders and threads. See page 122 for correct lubricant.

Clean the Threads

Clean the threads as needed with high-pressure water and detergent.

NOTICE:

Failure to follow this procedure could result in fused joints. Pipe will be damaged or destroyed.

NOTICE:

Do not use gasoline or other petroleum-based solvents. This prevents tool joint compound

from sticking to the joints and will reduce thread life.

Содержание JT5




























































































































































Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch JT5, Руководство оператора

Результаты поиска

Содержание JT5

Отзывы:

Бренды по названию

Популярные бренды