manualshive.com logo in svg

Ditch Witch 420sx, Руководство оператора

Поделиться
Скачать
Ditch Witch 420sx Скачать руководство пользователя страница 88

420sx Operator’s Manual

Systems and Equipment - 87

Plow Blades

Plow Blades

Blade Maintenance

•

Keep cable guide wing bolts tight. Loose cable guide bolts will break due to plow vibration.

•

Keep plow feed tube free of rock and debris so that material pulls freely though tube.

•

Use a speed blade only for straight or gently curving installations. Do not use speed blades for 
installations that require sharp turns.

•

Use the plow blade most appropriate for the type of material being installed. Contact your Ditch Witch 
dealer for information about the most effective blade for your jobsite conditions.

Blade Types

Type

Description

feed blade

used to “stitch” flexible material into the ground as it is fed through a chute or 
tube located at the back of the blade

speed blade

a thin feed-type blade used for high speed, straight plowing

pull blade

used to pull rigid or semi-rigid material into the ground through a tunnel made 
by a “bullet” at the bottom of the blade; a pulling grip is used to attach the material 
to the blade

Содержание 420sx














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды