DirecTV Advanced Installation Meter 2 Скачать руководство пользователя страница 58

Страница: 58 / 108

Page 58

AIM 2 Operation Manual

Performing EIV Following ODU Installation

When you complete the alignment process for the ODU, the EIV AT ODU screen appears.

You can:

•

Immediately perform Extended Installation

Verification (EIV) on the ODU that you just

aligned. Follow the steps below.

• If the installation includes two ODUs, you

can press

NEXT

to return to the

SELECT

ODU

screen and align the other ODU.

• Press

DONE

to return to the

HOME

screen

and perform EIV later. For instructions, see

the Performing EIV section.

To perform the Extended Installation Verification

(EIV) for the ODU that you just aligned:

1. On the EIV AT ODU screen, press RUN EIV

and wait briefly for the results.

2. On the EIV AT ODU RESULTS screen,

review the results for all supported orbital

slots and SWiM channels (if applicable).

A satisfactory result is indicated by a

checkmark. A problem is indicated by an X.
If a checkmark appears for all supported

orbital slots, the ODU alignment is

acceptable.
If X appears for an orbital slot, perform the

following steps:

• Press

REPEAT EIV

to confirm the

problem.

• If X appears again for one or more

orbital slots, you can press

EIV

DETAIL

to determine which tests

failed. Troubleshoot any failures

following the instructions provided by DIRECTV.

• To repeat the alignment process, press

REPEAT ALIGN

Содержание Advanced Installation Meter 2













































































































Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды

DirecTV Advanced Installation Meter 2, Руководство по эксплуатации

Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды