DirecTV Advanced Installation Meter 2 Скачать руководство пользователя страница 57

Страница: 57 / 108

Page 57

AIM 2 Operation Manual

Task F. Fine Azimuth Adjustment (Slimline ODUs Only)

1. Loosen the ODU’s azimuth lock-down screws.
2.

Turn the ODU’s azimuth jack screw

counterclockwise 2 turns.

3. On the

FINE AZ ADJ

screen, press

SET

REF

to set the reference value. The AIM

sounds a confirmation tone and displays the

reference value.

4. Zero out the readout dial on the azimuth

jack screw.

Turn the azimuth jack screw clockwise

until the meter begins to sound a series of

beeps, indicating that the reference value

is within 1 dB. Continue turning until the

meter sounds a confirmation tone and

the displayed signal power matches the

reference value (about 4 turns).

6. Refer to the ODU’s dial and use the AIM’s

numeric keypad to enter the number of turns

it took to return to the reference value

(e.g.

4.50 for four and a half turns)

. Then press

7. Zero out the readout dial on the azimuth

jack screw.

8. Refer to the AIM screen and turn the

azimuth jack screw counterclockwise the

number of turns indicated on the AIM

screen.

9. Tighten the azimuth lock-down screws.
10. Press

and then

NEXT

to continue

Содержание Advanced Installation Meter 2













































































































Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды

DirecTV Advanced Installation Meter 2, Руководство по эксплуатации

Результаты поиска

Содержание Advanced Installation Meter 2

Отзывы:

Похожие инструкции для Advanced Installation Meter 2

Бренды по названию

Популярные бренды