background image

Module Reset

Page 8

1

If required for your installation, connect the 10-pin & 12-pin 
harnesses to the module. Press and hold the programming 
button, then connect the 14-pin harness to the module.

10-pin

D2D

st

1

12-pin

14-pin

nd

2

th

4

rd

3

Warning Against Executing a Hard Reset! 

A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such 
as RFTD and D2D options) may have to be reconfigured. See the 

Feature & Option List 

section of this guide.

2

Solid

&

Release

3

 Release the programming button. The LED turns ON solid red.

Hard Reset

2

&

&

1

Wait 3 seconds until the LED turns ON solid orange then release the 
programming button. The LED turns ON solid red.

If required for your installation, connect the 10-pin & 12-pin 
harnesses to the module. Press and hold the programming 
button, then connect the 14-pin harness to the module.

10-pin

D2D

st

1

12-pin

14-pin

nd

2

th

4

rd

3

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed 
to the module using the web config tool will not be affected.

Solid

Release

Solid

Solid

Flashes

&

Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds 
until the LED starts to flash orange and red.

Press 

the PTS (Push-to-Start) button once to turn the Ignition 

OFF

.

1X

ENGINE

START

STOP

PUSH

4

5

The LED turns ON solid orange for 3 seconds, then shuts OFF.

&

Solid x3 Secs

Off

You have successfully completed the module programming sequence.

Rev.: 20170407

Platform: DBALL2
Firmware: GM9 Range Extender Ready (RXT) Installation v.2.05+

© 2017 Directed. All rights reserved.

Содержание XPRESSKIT GM9

















Отзывы: