manualshive.com logo in svg

Directed FORD5, Руководство по установке, Страница: 18 / 23

Поделиться
Скачать
Directed FORD5 Скачать руководство пользователя страница 18

18

Directed Digital Solutions FORD5

© 2016-03-17 Directed. All rights reserved.

LED diagnostics and troubleshooting

This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation.

Module programming

LED

Description

Troubleshooting

Off

Module has no power.

Make sure the D2D harness is connected or that the 12 Volt is present between the red and 

black wires. If the 12 Volt is present, the module may be defective.

Solid red

Waiting to begin the programming sequence. Make sure that all the connections are correct. See wiring diagram.

Flashes green

CAN detected.

Normal operation.

Solid orange

Waiting for Ignition ON.

Normal operation.

Flashes orange

Bypass was skipped.

Immobilizer bypass programming was skipped.

Flashes orange
slowly

Ready for Key2GO.

Normal operation. Follow the Key2GO programming.

Solid green  
x 3 secs

Module was successfully programmed.

Normal operation.

Solid orange  
x 3 secs

Module was successfully programmed without 

bypass.

Immobilizer bypass programming was skipped. Reset and start the programming sequence 

again.

Module programming - Error codes

LED

Description

Troubleshooting

Solid red

CAN2 not detected.

Check the Tan - Tan/Black wire connection.Turn the ignition on  to wake up the data bus and 

retry.

Solid red

Bypass data not detected.

Check the bypass line connection. If more than one wire is used, make sure they are not 

inverted. Start vehicle using the key to confirm the OEM equipment is still operational.

Solid red

Bypass processing error.

Bypass calculation failed. Reset the module and try again. Might be caused by a bad 

reading in the first programming attempt or by an unknown bypass value. If a second attempt 

fails, connect the module to Directechs and call Tech Support with the module ID in hand.

External module synchronization

LED

Description

Troubleshooting

  

  

(Flashes red, red, 
then orange) x 10

OBDII feature not supported.

Diagnostic data bus not detected. Some features are not supported by SmartStart. This can 

be caused by missing wire connections or module hardware limitation. Refer to "Installation 

(wiring diagrams & vehicle wiring reference charts)" to check the connections.

Active ground when running (status)

LED

Description

Troubleshooting

Flashes green

GWR (Status) command received.

Used to ensure the module has received the remote start message and has enabled the 

remote start runtime. Commands can come from RF or D2D.

  

Flashes red & 
orange

IGNITION ON command received.

Used to ensure the module received the ignition command.

Flashes green 
quickly

START ON command received.

Used to ensure the module received the start command.

Содержание FORD5
























Отзывы:

Нет отзывов