Directed Directechs FORD1, Руководство по установке, Страница: 58 / 66

58
DS4+ FORD1
© 2018-01-12 Directed. All rights reserved.
D2D port configuration
The system will automatically configure the D2D ports based on your selections in the module programming. The white D2D port is
reserved for SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming
of the DirectLink application or via the online web tool.
Note
: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor.
Module programming
Refer to "LED diagnostics and troubleshooting" on page 60 for more information and for troubleshooting purposes.
2-Key programming without Key2GO
(if only 1-key only, see"1-Key programming using Key2GO" on page 59)
To connect the module:
1
Please
ensure
that the vehicle is in a safe location and cannot move forward during
programming. For vehicles equipped with a manual transmission, make sure the gearshift
lever is in the neutral position.
2
Connect
all the harnesses to the DS4+,
EXCEPT
the 12-pin main power harness.
Connect all but the
12-pin harness
3
Connect
the 12-pin main power harness, and wait until the LED turns ON solid red.
Must be
connected LAST
&
Solid
4
Insert
the first key and
turn
it to the ON position,
wait
at least 3 seconds
but no more than 10 seconds then
remove
it. The LED turns ON solid red.
& &
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
1st
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
1st
Key at ON Key out after 3-10 sec.
Solid
5
Insert
the second key and
turn
it to the ON position,
wait
at least
3 seconds but no more than 10 seconds then
remove
it. The LED
now flashes orange, otherwise repeat steps 4 and 5.
& &
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
2nd
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
2nd
Key at ON Key out after 3-10 sec.
Flashes
Orange
6
Wait
for at least 3 seconds, but no more than 10 seconds, and
press
and
hold
the
programming button.The vehicle ignition turns ON.
The LED turns ON solid green for 3 seconds, then turns OFF. &
Solid
Green
Off
&
Press
& Hold
7
Turn
vehicle ignition OFF once the module is successfully programmed.
START
Key OUT
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
START
Key IN
ON
OFF
8
Pair
remotes (if applicable). For information on how to pair a specific remote, please
refer to its corresponding owner documentation, which can be found inside the product
packaging of the complete system or on www.directechs.com.*
Pair
remotes*
9
By default, the tachometer is preprogrammed for the vehicle. For instructions on how to
program tach, see page 63.
Initialize
tachometer
* Your aftermarket remote may differ from the model shown in the illustrations.
You have successfully completed the module programming sequence.