Directed Clifford 5606X Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 42

Directed Clifford 5606X Скачать руководство пользователя страница 24

20

© 2016 Directed. All rights reserved.

Alarm Report

If the alarm was triggered while armed, it will be reported when the
alarm is disarmed via siren chirps, parking light and Control Center
LED flashes. The siren chirps four times (or five times if NPC is ON*),
the parking lights flash three times, and the control center LED flashes
in groups to indicate the last two zones that were triggered (see

Table

of Zones

). The report output will repeat for each disarm operation until

the ignition is turned on.

* See

NPC (Nuisance Prevention Circuitry)

for more details.

Table of Zones

Zone # (led flashes)

Zone Name

1

Trunk

2

Shock Sensor

3

Door

4

Sensor 2

5

Ignition

6

Hood

NPC (Nuisance Prevention Circuitry)

NPC monitors all alarm zones and, if any are triggered excessively,
bypasses them until corrected. If a point of entry (trunk, hood, door)
is left open following a forced entry, it is bypassed. It becomes active
again only after being closed.

Bypassed sensors automatically reset after one hour and after the

vehicle is driven. Disarming then re-arming the alarm does not reset
bypassed sensors.

«
...
22
23
24
25
26
...
»

Содержание Clifford 5606X











































Отзывы:

Нет отзывов