Directed CHRYSLER4 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 23

Directed CHRYSLER4 Скачать руководство пользователя страница 16

Module programming

Refer to "LED diagnostics and troubleshooting" on page 17 for more information and for troubleshooting purposes.

To connect the module:

1

Please

ensure

that the vehicle is in a safe location and cannot move forward during

programming. For vehicles equipped with a manual transmission, make sure the gearshift
lever is in the neutral position.

2

Connect

all the harnesses to the Directed Digital Solutions,

EXCEPT

the 12-pin main power

harness.

Connect all but the

12-pin harness

3

Connect

the 12-pin main power harness, and wait until the LED turns ON solid red.

Must be connected LAST

&

Solid

4

Insert

the key in the ignition without turning it ON, wait for the LED to flash orange.

Flash

&

START

Key OUT

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

5

Turn

the key to the ON position. The LED will continue to flash orange. It will

then turn ON solid green or orange for 3 seconds before turning OFF.

Continue to

flash

Solid

Solid

&

OR

&

START

Key OUT

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

6

When green LED turns OFF,

turn

the ignition OFF and

remove

the key from the ignition.

The module is successfully programmed.

Off

&

START

Key OUT

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

START

Key IN

ON

OFF

7

Pair

remotes (if applicable). For information on how to pair a specific remote, please

refer to its corresponding owner documentation, which can be found inside the product
packaging of the complete system or on www.directechs.com.*

Pair

remotes*

8

DATA Tach: Firmware using DATA Tach, the tachometer is preprogrammed for the
vehicle and no further action is required. For instructions on how to adjust tach or use
Virtual tach, see page 20 (not needed with hardwired or data tach applications).

Hardwire Tach: Firmware using the Violet/White Hardwire Tach input will require
programming. For instructions on how to program or adjust tach or use Virtual tach, see
page 20 (not needed with hardwired or data tach applications).

Initialize

tachometer

* Your aftermarket remote may differ from the model shown in the illustrations.

You have successfully completed the module programming sequence.

16

Directed Digital Solutions CHRYSLER4

© 2019-05-15 Directed. All rights reserved.

«
...
14
15
16
17
18
...
»

Содержание CHRYSLER4
























Отзывы:

Нет отзывов