manualshive.com logo in svg

Directed 933.SUBARU2, Руководство по установке, Страница: 17 / 24

Поделиться
Скачать
Directed 933.SUBARU2 Скачать руководство пользователя страница 17

17

933.SUBARU2 1.38.195.3 2010 Subaru Outback
©2022 VOXX•DEI LLC.  All rights reserved.

Manual Transmission

IMPORTANT! 

Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles 

(EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, 
Honda S2000, Mazda Miata, and other such vehicles.

This system supports manual transmission installations. 

      

Refer to “Directwire” section at www.directechs.com for further information on vehicle-specific wiring connections.

When flashing the module for Manual Transmission on the Directechs website:

1.  In the 

Remote Start Features

 section, select the desired configurations for 

Manual Transmission Initialization

 & 

Manual Transmission 

Completion

.  

Manual Transmission Initialization

Sets how the manual transmission sequence is initialized

Remote (Default)

2x Parking Brake

1x Parking Brake

With foot on brake, set e-brake, remove foot brake, press ANY button on Directed 

remote. Ready mode is activated. Parking lights will flash 5 times confirming.

With foot on brake, setting the parking brake ON, OFF, ON within 10 seconds 

then removing foot brake will initialize the manual transmission ready mode. 

Parking lights will flash 5 times confirming.

Feature visible to Installer

With foot on brake, setting the parking brake ON then removing foot brake will 

initialize the manual transmission ready mode. Parking lights will flash 5 times 

confirming.

Manual Transmission Completion

Sets how the manual transmission sequence is ended.

Note 1

: For PTS vehicle specific instructions, please see the bottom of the “Vehicle Specific Install 

Guide” for manual transmission sequence procedures.

Note 2

: The trunk input trigger is considered a “door” for manual ready mode. If trunk or any other 

door is opened, manual transmission ready mode will be canceled.

Door closed & 

Remote (Default)

Door closed with 

passive locking

Door closed

To complete the manual ready mode sequence and shut down the remote start, 

turn off the ignition (engine stays running), exit the vehicle with your keys, shut all 

doors and press lock on the Directed remote.

To complete the manual ready mode sequence and shut down the remote start, 

turn off the ignition (engine stays running), exit the vehicle with your keys, 8 

seconds after the last door is closed, the remote starter will shut down, the door 

will automatically lock and the system will arm at the same time.

To complete the manual ready mode sequence and shut down the remote start, 

turn off the ignition (engine stays running), exit the vehicle with your keys, 8 

seconds after the last door is closed, the remote starter will shut down. Doors will 

stay unlocked.

Feature visible to Installer

2.  In addition, if no Clutch Output is pre-configured in the firmware, an output can be configured when flashing the module under the 

Programmable Input/Output

 section. Use any available positive (+) or negative (-) outputs depending on the polarity of the clutch 

switch listed on Directwire, set it to 

Starter

.

3. 

Note

: A Relay may be required depending on your vehicle.  

 
See Tech Tips 10000 - Clutch Bypass for Remote Start - 

https://directechs.blob.core.windows.net/techtips/10000.pdf

 

4.  Additional connections may be required if these functions are not supported by the firmware.

Connection

Description

(-) E-Brake Status Input 
(Black/White, pin 17)

Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple (-) trigger 
emergency brake circuits note some vehicles do not and may require unique integration methodologies.

(-) Door Trigger Input 
(Green, pin 20) OR (+) Door 
Input (Violet, pin 13)

Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor the door 
pins to allow the Ready Mode process to be enabled.

Note

: Some vehicles may require unique integration methodologies for this circuit. For more information, refer to 

www.directechs.com.

(AC) Tachometer Input 
(Violet/White, pin 22)

Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.) and 
learned successfully to the DS4+.

 
See Tech Tips 10001 - 

https://directechs.blob.core.windows.net/techtips/10001.pdf

Содержание 933.SUBARU2

























Отзывы:

Нет отзывов