background image

Warranty

LIMITED TWO YEAR CONSUMER WARRANTY:

Directed Electronics promises to the original purchaser, to replace this product should it prove to

be defective in workmanship or material under normal use, for a period of two years from the date

of purchase by the dealer as indicated by the date code marking of the product 

PROVIDED 

the

product was installed by an authorized Directed dealer. During this two year period, there will be

no charge for this replacement 

PROVIDED

the unit is returned to Directed, shipping pre-paid.  If

the unit is installed by anyone other than an authorized Directed dealer, the warranty period will

be 1 year from date of purchase by the dealer as indicated by the date code marking of the

product. During this 1 year period, there will be no charge for this replacement 

PROVIDED

the

unit is returned to Directed, shipping pre-paid. This warranty is non-transferable and does not

apply to any unit that has been modified or used in a manner contrary to its intended purpose,

and does not cover damage to the unit caused by installation or removal of the unit. This warranty

is void if the product has been damaged by accident or unreasonable use, neglect, improper service

or other causes not arising out of defects in materials or construction. 

ALL WARRANTIES

INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY

OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF NON-

INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE

MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR

AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE

SALE OF THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS

OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. 

Unit must be

returned to Directed, postage pre-paid, with: consumer's name, telephone number, and address,

authorized dealer's name and address, and product description.

IN ORDER FOR THIS WARRANTY

TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY AN

AUTHORIZED DIRECTED DEALER. ALL UNITS RECEIVED BY DIRECTED FOR WARRANTY

REPAIR WITHOUT PROOF OF DIRECTED DEALER INSTALLATION WILL BE COVERED BY THE

LIMITED 1 YEAR PARTS AND LABOR WARRANTY.

Note: This warranty does not cover labor costs

for the removal and reinstallation of the unit.

BY PURCHASING THIS PRODUCT, THE CONSUMER AGREES AND CONSENTS THAT ALL

DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE

WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.

© 2006 Directed Electronics,  All rights reserved.  G47505.10.15  05-06

H C C A - D 1 2 0 0
H C C A - D 2 4 0 0
H C C A - D 5 0 0 0

H C C A - D 1 2 0 0
H C C A - D 2 4 0 0
H C C A - D 5 0 0 0

Содержание HCCA-D2400

























Отзывы: