Dionex ICS-900 Скачать руководство пользователя страница 32

Страница: 32 / 142

ICS-900 Operator’s Manual

Doc. 065215-02 9/09

•

Sequence Control

provides controls for defining and running

sequences

(groups of sample injections to be analyzed in the order in

which they are listed).

•

Status

panel shows the overall system status.

•

autosampler

panel provides access to autosampler functions.

This panel is present only if the timebase in which the ICS-900 is
configured includes an autosampler.

To open the panel tabset, use one of the methods below:

•

If Chromeleon is installed,
start Chromeleon and click
the

Default Panel Tabset

toolbar button, or select

View > Default Panel
Tabset

•

If Chromeleon Xpress is
installed, start the application; this automatically displays the
ICS-900 panel tabset.

2.4.2

Software Control Modes

Two modes of software control are available: direct control and
programmed control.

•

With

direct

control, you select operating parameters and commands

from the Control panels. Direct control commands are executed as
soon as they are entered. See

Section 3.11.2

for details about direct

control.

•

With

programmed

control, you create a list of control commands to

be executed in chronological order. Programs can be created
automatically (with the help of a software wizard). See

Section 3.11.3

for details about programmed control.

Содержание ICS-900















































































































































Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды

Dionex ICS-900, Руководство оператора

Результаты поиска

Содержание ICS-900

Отзывы:

Похожие инструкции для ICS-900

Бренды по названию

Популярные бренды